Bem embalado, recebido em bom estado e prazo de entrega razoável (19 dias de calendário a partir da encomenda). A cablagem é um pouco estranha porque o interruptor de pressão não está conectado corretamente, mas é um mod fácil de consertá-lo. Funciona bem depois de feito.

Well packaged, received in good condition and reasonable delivery time (19 calendar days from order). The wiring is a bit strange because the push switch is not connected correctly, but it's an easy mod to fix it. It works well once that's done.

Bem embalado, recebido em bom estado e prazo de entrega razoável (19 dias de calendário a partir da encomenda). A cablagem é um pouco estranha porque o interruptor de pressão não está conectado corretamente, mas é um mod fácil de consertá-lo. Funciona bem depois de feito.

Good condition arrived in safe and all parts is ok! Good value/quality ratio. Thank you! :)

Good condition arrived in safe and all parts is ok! Good value/quality ratio. Thank you! :)

Good condition arrived in safe and all parts is ok! Good value/quality ratio. Thank you! :)

The encoder is OK, but the switch is NOT brought out to any pins, which means soldering, no matter what you do. Since the 'C' pin is directly connected to the GND pin, you can cut the trace on the back between the two pins, and wire one side of the switch to the old GND pin, and then wire the other side of the switch to either 'C' (the new GND pin) or to VCC. Normally you'll want the switch to GND as most micros have internal pull-up resistors, and it's less to wire in later. I've added a schematic of the debounce filtering on the photos below for your convenience. If you still have too much bounce, you might want to add up to .1uF caps on top of the existing 22nF capacitors. You may not need it. Since the description doesn't mention it, the encoder has 20 detents / positions per 360 revolution. I can't do a PREVIEW, so hopefully the photo comes through readable.

The encoder is OK, but the switch is NOT brought out to any pins, which means soldering, no matter what you do. Since the 'C' pin is directly connected to the GND pin, you can cut the trace on the back between the two pins, and wire one side of the switch to the old GND pin, and then wire the other side of the switch to either 'C' (the new GND pin) or to VCC. Normally you'll want the switch to GND as most micros have internal pull-up resistors, and it's less to wire in later. I've added a schematic of the debounce filtering on the photos below for your convenience. If you still have too much bounce, you might want to add up to .1uF caps on top of the existing 22nF capacitors. You may not need it. Since the description doesn't mention it, the encoder has 20 detents / positions per 360 revolution. I can't do a PREVIEW, so hopefully the photo comes through readable.

The encoder is OK, but the switch is NOT brought out to any pins, which means soldering, no matter what you do. Since the 'C' pin is directly connected to the GND pin, you can cut the trace on the back between the two pins, and wire one side of the switch to the old GND pin, and then wire the other side of the switch to either 'C' (the new GND pin) or to VCC. Normally you'll want the switch to GND as most micros have internal pull-up resistors, and it's less to wire in later. I've added a schematic of the debounce filtering on the photos below for your convenience. If you still have too much bounce, you might want to add up to .1uF caps on top of the existing 22nF capacitors. You may not need it. Since the description doesn't mention it, the encoder has 20 detents / positions per 360 revolution. I can't do a PREVIEW, so hopefully the photo comes through readable.

muito feliz com este item!

Very happy with this item!

muito feliz com este item!

Exactamente ou que eu pretendia

exactamente o que pretendia

Exactamente ou que eu pretendia

Conforme descrito, chegou dentro de um prazo razoável.

As described. Arrived in reasonable time.

Conforme descrito, chegou dentro de um prazo razoável.

Está bem, está bem

ok

Está bem, está bem

Está bem, está bem

OK

Está bem, está bem

Excelente componente, fácil de usar com o Arduino.

Excellent component, easy to use with Arduino.

Excelente componente, fácil de usar com o Arduino.

não pode dar errado com estes

Can't go wrong with these

não pode dar errado com estes