Opiniões dos clientes

5 de 5
Escrever uma crítica
  • Todos Comentários (34)
  • Imagem (6)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(34)
    • Estrela(34)
    • Estrela(0)
    • Estrela(0)
    • Estrela(0)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Mozambique)
  • August-16 2020 03:22:34

    Excellent. My recommendations

    Comentários
  • August-03 2017 05:53:11

    Very useful adapter if you want to use it with breadboards. On the back there is a possibility to add a voltage regulator. I like to use it as a 3.3V input (using a MB102 Breadboard Module Adapter Shield 3.3V/5V or 5V-3.3V DC-DC AMS1117 800MA Step-Down Power Supply) to provide the 3.3V input. So if you want to use it as 3.3V input, you need to connect it on the back as shown on the photo. The adapter is quite wide using up the whole mid section of the breadboard. This is no issue as the wires can

    Comentários (2)
  • October-20 2017 13:27:55

    Parfait pour flasher les ESP8266 12E, avant d'avoir ces platines je n'arrivais pas à flasher correctement. Maintenant c'est correct je ne rate plus rien.

    Comentários
  • September-26 2017 18:39:57

    I was looking for some easy way to solder the ESP8266 and finally I found it.

    Comentários
  • April-11 2017 05:10:02

    Ordinati il 23 marzo ho scelto la spedizione con Priority Direct Mail; sono arrivati l'11 aprile. Come da descrizione. Imballo perfetto.

    Comentários
  • June-06 2018 10:14:15

    Thank you for your delivery. The goods arrived in order. I'm looking forward to working with it.

    Comentários
  • June-11 2020 11:59:06

    good adapter for ESP12S

    Comentários
  • May-27 2020 06:23:39

    Great price, good quality.

    Comentários
  • September-08 2016 15:41:58

    Good little breakout board, very satisfied so far - not so easy to find them. A bit of extra information, that is not included in the product description, but I would have loved to know upfront: The distance betweet the two pin rows is about 28mm (or 1.1inch), so its footprint on a standard breadboard is 12 by 8. The voltage regulator is easy so solder on, but don't forget to desolder the 0Ohm fuse resistor in the middle then - the size (package) you need is a SOT89. Tried it with some 78L33, but

    Comentários
  • June-18 2017 22:54:49

    So far these are pretty good. Soldering the ESP 8266 SMD is fairly simple if you know how to solder. However, soldering the pin headers was a little more difficult. The metal rings in the holes for the pins are very small and it was a bit difficult to get the solder to flow without flux. I try to avoid flux when possible because it's sticky and messy but after one pin i went straight to the flux. Also, the pins extend all the way out the breadboard. So if you want to use this on a breadboard, which

    Comentários
Show:

    Total 0 pages

    Go to page

    Go

    Você pode estar interessado em

    recommendation for you
    • US$27.99
    • US$2.49
    • US$12.47
    • US$3.59
    • US$4.99
    • US$4.99
    • US$4.99
    • US$5.13
    • US$3.11
    • US$1.99
    • US$3.99
    • US$2.99
    • US$10.99
    • US$3.38
    • US$10.99
    • US$2.55
    • US$4.99
    • US$5.25