Opiniões dos clientes

4.95 de 5
Escrever uma crítica
  • Todos Comentários (1517)
  • Imagem (187)
  • Vídeo (5)
  • Todas as estrelas
    • Todas as estrelas(1517)
    • Estrela(1459)
    • Estrela(51)
    • Estrela(2)
    • Estrela(2)
    • Estrela(3)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Mozambique)
  • February-06 2020 02:24:08

    Заказал 01.29 получил 02.06. Мотор рабочий. выглядит уверенно! На 4 фотке разница 775 с мотором из шурика.

    Comentários
  • March-13 2020 03:44:35

    They all work as expected. Draws around 0.33A at 12V 0.45A at 24V. Low noise even at 24V.

    Comentários (1)
  • September-10 2020 13:04:23

    late delivery but its understandable.

    Comentários
  • June-30 2020 12:28:27

    Llego en perfectas condiciones, muchas gracias

    Comentários
  • September-14 2020 11:33:05

    Amazing torque! These motors can do a lot of work without a gearbox. Good for direct drive in a bigger r/c tugboat.

    Comentários
  • August-25 2020 18:08:20

    Very good product. Works fine

    Comentários
  • November-24 2019 05:04:27

    These are some very cheap very powerfull very robust motors. I use them in a lot of projects. I made 2 Servo's/actuators with them. Video's can be found here: 3D-printed linear actuator -> https://youtu.be/99aw_77oUvY 3D-printed high torque servo/gear reduction -> https://youtu.be/8sq4pHdSXYM

    Comentários (2)
  • April-15 2019 10:00:11

    The engine delivered well and fast enough. I tried it right away - it starts spinning at 0.7V and I tested it up to 30V You can look at RPM for several measurements. I am very satisfied width it, only the engine running is a bit irregular and is also quite noisy. I'll use it to drive a small table saw.

    Comentários
  • December-01 2017 06:31:14

    Packaging is not so secure as expected wraping only with foam and plastic bag. I ordered 4 motors ... two of them, their shafts can be easily winded by hand but not for the other two that need pliers to turn the rotors.. All motors work fine with 12 Vdc (I don't have other tools to test their characteristics by now).

    Comentários
  • July-19 2017 02:42:25

    Отличный и мощный электродвигатель имеет толстый вал 5 мм с переди посажен на подшипник 625Z ,а сзади на подшипник латунный. Также имеются отверстия для крепления М4.Отлично подходит для изготовления мини станочков, цена меньше чем в других магазинах.

    Comentários
Show:

    Total 0 pages

    Go to page

    Go

    Você pode estar interessado em

    recommendation for you
    • US$4.99
    • US$8.48
    • US$7.71
    • US$15.99
    • US$17.51
    • US$21.99
    • US$17.99
    • US$12.25
    • US$23.35
    • US$9.39
    • US$3.99
    • US$3.17
    • US$13.27
    • US$8.48
    • US$11.56
    • US$4.23
    • US$9.99
    • US$12.99