First things first. If you are the kind of person that wants to click one button and everything works perfectly this is not for you. for everybody else its a decent printer. Build time 4 hours, everything you need is provided. Tweaking and getting it to run good took me another 2-4 hours. Things that are great: - Stable frame - Heated bed that provides really good bed adhesion (almost too good) - Complete kit Things that could be better: - The support frame for the y axis is very thin. If you are fighting to remove a print from the bed you can and will bend it slightly. And this means you will have to adjust the bed level again. - My bed wasn't perfectly flat, this can be problematic for larger prints. but is easily solved by using a glass plate or a raft during printing. - the hot end fan is controlled by the cooling fan pwm. This is not OK and I had to change this. If you were to run a print without the cooling fan enabled your hotend will overheat and clog up. I opened the control box and rewired the fan to the 12V rail to be always on. Do change this!! - micro SD slot.... awfull. I had several occations where i tried to push in the sd card and missed the actual port. then you have to open up the control box to get your micro sd card back. Do yourself a favour and get a micro to sd adapter http://tiny.cc/023huy Things to watch out for - spend a little time adjusting all the eccentric bearing bushings. too much pressure causes them to wear quickly - print yourself a filament guide to prevent the filament from touching the Z axis. - don't try to print too fast, the extruder will be your limiting factor here, you could consider upgrading this. All in all, not too bad, not too bad at all Cheers!

First things first. If you are the kind of person that wants to click one button and everything works perfectly this is not for you. for everybody else its a decent printer. Build time 4 hours, everything you need is provided. Tweaking and getting it to run good took me another 2-4 hours. Things that are great: - Stable frame - Heated bed that provides really good bed adhesion (almost too good) - Complete kit Things that could be better: - The support frame for the y axis is very thin. If you are fighting to remove a print from the bed you can and will bend it slightly. And this means you will have to adjust the bed level again. - My bed wasn't perfectly flat, this can be problematic for larger prints. but is easily solved by using a glass plate or a raft during printing. - the hot end fan is controlled by the cooling fan pwm. This is not OK and I had to change this. If you were to run a print without the cooling fan enabled your hotend will overheat and clog up. I opened the control box and rewired the fan to the 12V rail to be always on. Do change this!! - micro SD slot.... awfull. I had several occations where i tried to push in the sd card and missed the actual port. then you have to open up the control box to get your micro sd card back. Do yourself a favour and get a micro to sd adapter http://tiny.cc/023huy Things to watch out for - spend a little time adjusting all the eccentric bearing bushings. too much pressure causes them to wear quickly - print yourself a filament guide to prevent the filament from touching the Z axis. - don't try to print too fast, the extruder will be your limiting factor here, you could consider upgrading this. All in all, not too bad, not too bad at all Cheers!

First things first. If you are the kind of person that wants to click one button and everything works perfectly this is not for you. for everybody else its a decent printer. Build time 4 hours, everything you need is provided. Tweaking and getting it to run good took me another 2-4 hours. Things that are great: - Stable frame - Heated bed that provides really good bed adhesion (almost too good) - Complete kit Things that could be better: - The support frame for the y axis is very thin. If you are fighting to remove a print from the bed you can and will bend it slightly. And this means you will have to adjust the bed level again. - My bed wasn't perfectly flat, this can be problematic for larger prints. but is easily solved by using a glass plate or a raft during printing. - the hot end fan is controlled by the cooling fan pwm. This is not OK and I had to change this. If you were to run a print without the cooling fan enabled your hotend will overheat and clog up. I opened the control box and rewired the fan to the 12V rail to be always on. Do change this!! - micro SD slot.... awfull. I had several occations where i tried to push in the sd card and missed the actual port. then you have to open up the control box to get your micro sd card back. Do yourself a favour and get a micro to sd adapter http://tiny.cc/023huy Things to watch out for - spend a little time adjusting all the eccentric bearing bushings. too much pressure causes them to wear quickly - print yourself a filament guide to prevent the filament from touching the Z axis. - don't try to print too fast, the extruder will be your limiting factor here, you could consider upgrading this. All in all, not too bad, not too bad at all Cheers!

(cliente do Reino Unido) Esta é a minha primeira impressora (Tenho experiência anterior com impressoras de nível industrial, mas não com máquinas de consumo) Não consigo falar suficientemente desta impressora. veio em 48 horas e muito bem embalado (não havia marcas na caixa, mas nada de importante). Levei cerca de 45-50 minutos para montar e verificar (recomendar vídeos online para a construção como as instruções começar o trabalho feito, mas são muito caóticos e não muito claros). Usei o filamento incluído que foi mais do que suficiente para o cão de teste de impressão que escolhi (100% de enchimento) e saiu muito bem, sem problemas, houve um pouco de ligação com a cauda e as orelhas, mas era esperado diretamente da caixa. Aviso de configuração: - Verifique se você tem um bom espaço para trabalhar (trate-o como se fosse construir um PC ) - Nivelar a cama 3-4 vezes antes de começar a imprimir - Verifique todas as porcas e parafusos, deixe a impressora oscilar ligeiramente para ver se consegue ouvir peças soltas - Verifique as esteiras, certifique-se de que estão livres e tensas para uma execução suave. - Use vídeos on-line para referência e veja o display e as configurações antes de começar, para que você esteja familiarizado com todas as configurações e menus.

(UK customer) This is my first printer (I have had previous experience with industry grade printers but not consumer machines) I cannot speak highly enough of this printer. came within 48 hours and very well packaged (there were dents on the box but nothing major). Took me about 45-50 mins to assemble and check (recommend online videos for construction as the instructions get the job done but are very chaotic and no very clear). Used the filament included which was more than enough for the test print dog I chose (100% Fill) and It came out really well, no issues, there was a bit of bridging with the tail and ears but to be expected straight out of the box. Setup advice: - make sure you have a good space to work on (treat it like building a PC ) - level the bed 3-4 times before you start printing - check all nuts and bolts, give the printer a slight wobble to see if you can hear any loose parts - check the belts make sure they are clear and tensioned for a smooth run. - use videos online for reference and have a look through the display and settings before starting so you are familiar with all the settings and menus.

(cliente do Reino Unido) Esta é a minha primeira impressora (Tenho experiência anterior com impressoras de nível industrial, mas não com máquinas de consumo) Não consigo falar suficientemente desta impressora. veio em 48 horas e muito bem embalado (não havia marcas na caixa, mas nada de importante). Levei cerca de 45-50 minutos para montar e verificar (recomendar vídeos online para a construção como as instruções começar o trabalho feito, mas são muito caóticos e não muito claros). Usei o filamento incluído que foi mais do que suficiente para o cão de teste de impressão que escolhi (100% de enchimento) e saiu muito bem, sem problemas, houve um pouco de ligação com a cauda e as orelhas, mas era esperado diretamente da caixa. Aviso de configuração: - Verifique se você tem um bom espaço para trabalhar (trate-o como se fosse construir um PC ) - Nivelar a cama 3-4 vezes antes de começar a imprimir - Verifique todas as porcas e parafusos, deixe a impressora oscilar ligeiramente para ver se consegue ouvir peças soltas - Verifique as esteiras, certifique-se de que estão livres e tensas para uma execução suave. - Use vídeos on-line para referência e veja o display e as configurações antes de começar, para que você esteja familiarizado com todas as configurações e menus.

Hai this is my first 3d pritner, in mine printer i got injecton moulded power supply cover, where has shashi got 3d printed one. The printer is assembled and working the first print quality also nice. Thanks for every one

Hai this is my first 3d pritner, in mine printer i got injecton moulded power supply cover, where has shashi got 3d printed one. The printer is assembled and working the first print quality also nice. Thanks for every one

Hai this is my first 3d pritner, in mine printer i got injecton moulded power supply cover, where has shashi got 3d printed one. The printer is assembled and working the first print quality also nice. Thanks for every one

05076700387 ürün hakkında sorusu olan arayabilir yardımcı olurum

05076700387 ürün hakkında sorusu olan arayabilir yardımcı olurum

05076700387 ürün hakkında sorusu olan arayabilir yardımcı olurum

The printer is good strong in structure. the assemble is simple and all assembly instruction given in manual as well as memory card which helps to assemble withe ease. The printer assembly which is DIY i am loving it. The printer prints also well. i have to adjust the print settings. The printer has some minor issues we faced during installation like x carriage and z carriage or not moving through the aluminium T slot because of slight variation in the measurements. that is solved just simply by loosing the nuts of bearing.

The printer is good strong in structure. the assemble is simple and all assembly instruction given in manual as well as memory card which helps to assemble withe ease. The printer assembly which is DIY i am loving it. The printer prints also well. i have to adjust the print settings. The printer has some minor issues we faced during installation like x carriage and z carriage or not moving through the aluminium T slot because of slight variation in the measurements. that is solved just simply by loosing the nuts of bearing.

The printer is good strong in structure. the assemble is simple and all assembly instruction given in manual as well as memory card which helps to assemble withe ease. The printer assembly which is DIY i am loving it. The printer prints also well. i have to adjust the print settings. The printer has some minor issues we faced during installation like x carriage and z carriage or not moving through the aluminium T slot because of slight variation in the measurements. that is solved just simply by loosing the nuts of bearing.

Excelente escolha para a pessoa com um orçamento lo. Claro que há modelos melhores, mas preço/eficiência eu acho difícil de superar. Também é possível fazer muitos ajustes de ajuste de posição na configuração. Um aspecto negativo são os parafusos de nivelamento. É muito difícil pô-los a trabalhar juntos. Também gosto de ter que montá-lo todo da caixa, um pouco educacional comparado a uma máquina RTP. Definitivamente compraria outra vez se de alguma forma este fosse roubado ou pegado fogo, 🤣

Excellent choice for the person with a lo budget. Of course there is better models, but price/efficiency I think it's hard to beat. You can make a lot of tweaking in the setup as well. One negative aspect is the leveling screws. It's pretty hard to getting them all to work together. Also I like that I have to assemble it all together from the box, a bit educational compared to a RTP machine. I would definitely buy one again if somehow this one gets stolen or set on fire. 🤣

Excelente escolha para a pessoa com um orçamento lo. Claro que há modelos melhores, mas preço/eficiência eu acho difícil de superar. Também é possível fazer muitos ajustes de ajuste de posição na configuração. Um aspecto negativo são os parafusos de nivelamento. É muito difícil pô-los a trabalhar juntos. Também gosto de ter que montá-lo todo da caixa, um pouco educacional comparado a uma máquina RTP. Definitivamente compraria outra vez se de alguma forma este fosse roubado ou pegado fogo, 🤣

after using anet a8 for 7 months I got this ender 3 it's so good printer also amazing price

after using anet a8 for 7 months I got this ender 3 it's so good printer also amazing price

after using anet a8 for 7 months I got this ender 3 it's so good printer also amazing price

Excelente produto. Fui tarifado em R$511,00.

Excelente produto. Fui tarifado em R$511,00.

Excelente produto. Fui tarifado em R$511,00.

Chegou tudo corretamente e funcionando perfeitamente. Recomendo.

Chegou tudo corretamente e funcionando perfeitamente. Recomendo.

Chegou tudo corretamente e funcionando perfeitamente. Recomendo.

Très bonne imprimante, aucun problème avec elle est top pour sont prix. Seule demol c'est de la réglé le calibrage pour l'impression c'est casse couille à faire et il faut être très patient. J'ai mis plus 1 semaine pour l'avoir en main et comprendre heureusement que y'a YouTube lol 😂 . Programme en Anglais mais facile à comprendre.

Très bonne imprimante, aucun problème avec elle est top pour sont prix. Seule demol c'est de la réglé le calibrage pour l'impression c'est casse couille à faire et il faut être très patient. J'ai mis plus 1 semaine pour l'avoir en main et comprendre heureusement que y'a YouTube lol 😂 . Programme en Anglais mais facile à comprendre.

Très bonne imprimante, aucun problème avec elle est top pour sont prix. Seule demol c'est de la réglé le calibrage pour l'impression c'est casse couille à faire et il faut être très patient. J'ai mis plus 1 semaine pour l'avoir en main et comprendre heureusement que y'a YouTube lol 😂 . Programme en Anglais mais facile à comprendre.