Enviar para United Kingdom , USD

Opiniões dos clientes

4.94 de 5
Escrever uma crítica
  • Todos Comentários (904)
  • Imagem (192)
  • Vídeo (5)
  • Todas as estrelas
    • Todas as estrelas(292)
    • Estrela(278)
    • Estrela(13)
    • Estrela(0)
    • Estrela(1)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
    • Geral:
    • Preço:
    • Qualidade:
    • Aparência:

    2020-02-28 06:00:29

    Best flight controller in the price range. Make a note that this is a 20x20 stack....and most suitable for 3-5'' quads Few things to note for new bees: 1. Use a voltmeter to make sure you don't fry the electronics 2. Practice soldering before jumping on FC (it has tiny pads for the camera, vtx, and receiver) 3. After my first wiring, I ended up with one motor not appear in BLHELI and changing the wire between the flight controller and ESC helped fix it. Please see the picture for the build mounted

    Comentários (1)
    • Geral:
    • Preço:
    • Qualidade:
    • Aparência:

    2020-06-14 22:33:12

    exactly as advertised, the performance is great, this and f411 are my go to stacks. the pads are small so make sure your soldering skills are up to par, if you have shaky hands you may be in for a bit of a headache. but if your good with that you will be hard pressed to find fault with these boards..... 10 out of 10 highly recommended.

    Comentários
    • Geral:
    • Preço:
    • Qualidade:
    • Aparência:

    2019-10-23 10:59:28

    Its a pretty good stack. The solder points are very small and close together so be very careful and maybe even use a magnifying light to work on them. I have it running Betaflight 4.06 on a 6 inch Floss. It does really well. Super light and as long as you don't mind re-mapping the PPM pin to a soft serial to run Smart Audio, you have plenty of UARTS to handle a GPS and an FRsky Receiver with telemetry.It does

    Comentários
    • Geral:
    • Preço:
    • Qualidade:
    • Aparência:

    2019-10-22 05:12:38

    У меня небыло xt30 в комплекте, но зато положили длинные винты с силиконовыми колечками, для установки через раму, на работоспособность не проверял, но на вид всё неплохо

    Comentários
    • Geral:
    • Preço:
    • Qualidade:
    • Aparência:

    2019-08-21 08:13:32

    very good stack with F4 FC and a 20A ESC's 4 in 1 board. I have order from EU and got the 20A version. If you order from CN you get the newest version with 25A (30A burst) ESC's board

    Comentários
    • Geral:
    • Preço:
    • Qualidade:
    • Aparência:

    2019-09-20 22:26:53

    Grosse déception pour cette stack qui a pris pas mal de temps pour me parvenir( malgré une envoi en express) mais ne voila t’il pas que les esc 4en1 ne fonctionne pas. un des moteurs ne tourne pas quand j’active les moteurs la deuxième foi. le quad était près pour la configuration

    Comentários
    • Geral:
    • Preço:
    • Qualidade:
    • Aparência:

    2019-12-07 02:18:18

    Богатая комплектация. Отличное качество изготовления. Быстрая доставка.

    Comentários
    • Geral:
    • Preço:
    • Qualidade:
    • Aparência:

    2019-12-05 03:59:56

    best price and quality for a 20x20mm F4 stack with 25A ESC's I have order from UK and got the newest 25A ESC's Mamba stack version.

    Comentários
    • Geral:
    • Preço:
    • Qualidade:
    • Aparência:

    2020-05-18 06:43:11

    Superbe carte. Toutes les pastilles de soudures de la FC sont troué, ce qui permet de mettre les câbles et de les souder correctement et proprement. Les vis pour monter les stack peuvent être assez courte si vous compter sur élever la PDB de 5mm. Avec bottom plate de 4mm, élévation de 5mm. les vis, fournit d'origine sont légèrement trop courtes, et ceux même avec la seconde configuration de vis fournit. Aucun connecteur XT fournit, mais des câbles en 18 AWG sont présent. Attention j'ai

    Comentários
    • Geral:
    • Preço:
    • Qualidade:
    • Aparência:

    2019-11-07 09:44:28

    Umm it's good if you get working unit use silicone cables they are better soldering on it's pad is bit difficult as they leave black residue.. they are super noise free and if you get hot motor at default filters then rasie gyro dynamic min to 300hz and Max to 850 hz and you'll be Good to go

    Comentários
  1 2 3 4 5 6 7 8 9 10 ... 91  

Você pode estar interessado em

Exame de Satisfação

Faça o download do aplicativo para receber um cupom exclusivo de 10% de desconto