Comentários de Placa de controle de voo Eachine Beecore F3_EVO_Brushed para Inductrix Tiny Whoop Eachine E010 E010S - Banggood Portugal Online Shopping

Placa de controle de voo Eachine Beecore F3_EVO_Brushed para Inductrix Tiny Whoop Eachine E010 E010S

US$33.48
~~US$34.99~~
Compre agora

Opiniões dos clientes

4.88 de 5

Ver todos 758 comentários

5 estrela
697 (92.0%)
4 estrela
40 (5.3%)
3 estrela
12 (1.6%)
2 estrela
6 (0.8%)
1 estrela
3 (0.4%)

Escrever uma crítica Obtenha o dobro de pontos de comentário,se você é um dos primeiros 3 comentários publicados!

Todos Comentários (758)
Imagem (97)
Vídeo (21)
Todas as estrelas
- Todas as estrelas(758)
- Estrela(697)
- Estrela(40)
- Estrela(12)
- Estrela(6)
- Estrela(3)

Ordenar por:

Comentários Anteriores

Comentários Anteriores
Mais úteis
Mais Recente

Comentários apenas do seu país (Portugal)

|

Mostrar original

Uma parte da revisão foi traduzida automaticamente.

AaronVIP1
US
19/01/2017

I thought I might have to return it after a day of frustration, but after doing some research and persistence I was finally successful. For those who have the FlySky FS-I6 AFHDS 2A transmitters, follow the PDF instructions provided on this site until you get to step "3. Binding Procedure" a) On my FS-I6 it shows AFHDS 2A (On/Off). I selected "Off", which I assume selects AFHDS, and not AFHDS 2A. b) Then follow the rest of the procedures and your transmitter will show "RxBinding" as you power it on with the binding jumpers connected. Watch the flashing green LEDs on the board. When it shows solid green, you are now successful, even though your transmitter still displays "RxBinding". Power off your receiver and beecore, and when you power them up again, you should be good to go!

I thought I might have to return it after a day of frustration, but after doing some research and persistence I was finally successful. For those who have the FlySky FS-I6 AFHDS 2A transmitters, follow the PDF instructions provided on this site until you get to step "3. Binding Procedure" a) On my FS-I6 it shows AFHDS 2A (On/Off). I selected "Off", which I assume selects AFHDS, and not AFHDS 2A. b) Then follow the rest of the procedures and your transmitter will show "RxBinding" as you power it on with the binding jumpers connected. Watch the flashing green LEDs on the board. When it shows solid green, you are now successful, even though your transmitter still displays "RxBinding". Power off your receiver and beecore, and when you power them up again, you should be good to go!

I thought I might have to return it after a day of frustration, but after doing some research and persistence I was finally successful. For those who have the FlySky FS-I6 AFHDS 2A transmitters, follow the PDF instructions provided on this site until you get to step "3. Binding Procedure" a) On my FS-I6 it shows AFHDS 2A (On/Off). I selected "Off", which I assume selects AFHDS, and not AFHDS 2A. b) Then follow the rest of the procedures and your transmitter will show "RxBinding" as you power it on with the binding jumpers connected. Watch the flashing green LEDs on the board. When it shows solid green, you are now successful, even though your transmitter still displays "RxBinding". Power off your receiver and beecore, and when you power them up again, you should be good to go!
48

Comentários (4)

Mostrar original
igyigyVIP1
US
17/11/2016

From the CLI dump, this is the version info # version # Cleanflight/SPRACINGF3EVO 1.13.0 Jun 6 2016 / 00:03:29 (a77bc76) I have yet to solder power and fly it. Will be flashing betaflight

From the CLI dump, this is the version info # version # Cleanflight/SPRACINGF3EVO 1.13.0 Jun 6 2016 / 00:03:29 (a77bc76) I have yet to solder power and fly it. Will be flashing betaflight

From the CLI dump, this is the version info # version # Cleanflight/SPRACINGF3EVO 1.13.0 Jun 6 2016 / 00:03:29 (a77bc76) I have yet to solder power and fly it. Will be flashing betaflight
18

Comentários (2)

Mostrar original

Show:

Total 0 Páginas

Vá para página

Vai

Você pode estar interessado em

recommendation for you