Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (151)
  • Imagem (2)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(151)
    • Estrela(136)
    • Estrela(12)
    • Estrela(3)
    • Estrela(0)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Portugal)
|
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 15/03/2017

    I got this today and set it up. So far it's just as advertised and I am happy with the purchase. A tip for those who are buying this. I suggest you look closely at the pictures on banggood. The spacing on the standee's only really works one way, using the screws from the bottom of the acrylic to screw into the nut part of the standee. The standee screws then go into the raspberry pi's bottom and finally the nuts go on top. This makes it a bit tricky to get the tiny little nuts on snug as they are somewhat close to some of the components on the raspberry pi. If done differently there will be a bit of space between the screws and standees which will allow the raspberry pi to wiggle.

    Comentários
    Mostrar original
  • 19/10/2015

    Received my order in 9 days, All screws, cables, and accessories arrived complete. Overall I am very happy with the purchase. PRO: Arduino Uno R3 and RPi-B both fit perfectly. Everything is positioned intelligently for easy access to all sockets and peripherals. There is a handy opening on the bottom that allows access to the memory card reader on the RPi. Accessory cables are perfect for quick connectivity to the RPi, but not the Ardiono. Ribbon cable is ideal length for folding neatly when connected to the RPi GPIO adapter. The included Dupont ribbon jumpers are very handy and contain the exact number of jumpers needed to connect all IO pins on the RPi. Unfortunately, these jumpers are M-F so they do not work with Arduino. CON: The Dupont jumpers are a bit short.. They do not reach from the top corner of the RPi to the bottom corner of the breadboard. The Dupont jumpers are M-F, perfect for RPi, but useless for an Arduino. This allows us two ways to connect to the RPi, but no way to connect to an Arduino. The RPi GPIO adapter is very handy but the pins connecting to the breadboard are excessively wide - wasting three breadboard pins every row. This may be a design consideration to make the adapter stronger, so it is probably better that it is so wide. However, the pins are arranged such that the adapter cannot be placed center on the breadboard. This is a benign cosmetic issue, but it will definitely irritate those who are obsessive-compulsive. Because of the non-center problem, I gave this item only four stars for appearance. Suggestions: - The Dupont jumpers should be at least two inches longer - Replace the M-F jumpers with M-M jumpers to allow connectivity with Arduino - Include rubber feet to protect the bottom of the board - Space the pins on the GPIO adapter such that the adapter can be centered on the breadboard

    Comentários
    Mostrar original
  • 14/02/2017

    very helpful

    Comentários
    Mostrar original
  • 01/03/2016

    Item received was just as pictured on the web site. Quality of plexi-glass mounting plate was very good. My UNO board and Raspberry Pi 2B fit perfectly using the mounting hardware provided. The Pi's GPIO adaptor board used with the solder-less breadboard worked good but it unnecessarily covered up component holes on the breadboard. I found I could file one edge of the adaptor where there were no circuit traces to reduce its width. This allowed access to more component holes (I am NOT suggesting others do this...it worked nicely for me. My only complaint is that the solder-less breadboard was a bit "warped" and did not want to stay adhered to the plexi-glass base along its entire length. A minor issue that does not interfere with its use. A very good value from Banggood in my opinion and will recommend it to others.

    Comentários
    Mostrar original
  • 15/03/2021

    PRECISA DE MELHORAR A EMBALAGEM DA PRÓXIMA VEZ, A CARTÃO EXPERIMENTAL É BORDADA NA Metade, DURANTE O ENVIAMENTO. OS ACESSÓRIOS NO MESMO ENVIAMENTO ESTÃO EM BOM ESTÃO ACEITÁVEL, DOIS LÍDERES curvados, MAS ESTÁ OK.

    Comentários (1)
    Mostrar original
  • 05/10/2016

    This is a totally reasonable setup. The base is not brittle and seems durable, the posts are decently made. It fit my pi2 without any trouble. It comes with little silicon/polymer feet, but only 4, the size is such that another 4 would be nice to prevent flex during operation.

    Comentários
    Mostrar original
  • 24/07/2016

    If you want to play with some projects based on raspberry pi, this one is must to have. In the past I used to solder my prototypes. Not any more :-)

    Comentários
    Mostrar original
  • 10/04/2016

    Perfect size to hold MEGA and the other larger Arduino units!

    Comentários
    Mostrar original
  • 23/02/2016

    Instead of a Raspberry I mounted an Orange (but I had to drill two extra holes for it) and instead of an Uno I tried to mount a nano and failed. the GPIO cable fits well but seems to get in the way. the breadboard and the jumper wires seem of good quality.

    Comentários
    Mostrar original
  • 23/01/2016

    Indispensable pour des montages avec interfaces externes, surtout quand on manipule de la basse tension .

    Comentários
    Mostrar original
Show:

    Total 0 Páginas

    Vá para página

    Vai

    Você pode estar interessado em

    recommendation for you
    • US$32.99
    • US$12.99
    • US$19.55
    • US$11.49
    • US$11.49
    • US$16.09
    • US$19.54
    • US$38.55
    • US$9.99
    • US$6.99
    • US$25.64
    • US$54.99
    • US$11.72
    • US$13.99
    • US$12.99
    • US$20.69
    • US$11.19
    • US$11.99