Opiniões dos clientes

4.98 de 5
Escrever uma crítica
  • Todos Comentários (179)
  • Imagem (12)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(179)
    • Estrela(176)
    • Estrela(3)
    • Estrela(0)
    • Estrela(0)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
  • roel
    2020-07-29 09:02:55

    Overall a nice block. Arrived well oiled in a box marked 'square block' so I was worried for a bit that this may be the square version but it was the hex version indeed. There was a bit of damage to the thread but that cleaned up nicely. Tested with some collets and they fit nicely. With some silver steel bar inside and an indicator I could see that the hole is nicely centered.

  • Romero
    2019-10-28 01:44:50

    Todo correcto llego en tiempo el bloque ER-32 se desliza muy suave bien lubricado terminación correcta dentro de su relación de calidad y precio, pare una pieza fuerte de acero duro con su rosca para las pinzas. Saludos gracias.

  • 2020-03-07 10:19:28

    Ce porte-pince correspond tout à fait à ce que j'attendais. Peut être utilisé sur un tour ou une fraiseuse et permet de bloquer des arbres ou des outils jusqu'à 20 mm de diamètre quand on dispose de pinces ER 32. Belle fabrication.

  • JanErik
    2019-10-27 09:36:17

    Good quality.

  • ferko
    2020-01-30 16:35:41

    Výborný přípravek na jednoduché frézování šestihranu. Okamžitě jsem to musel vyzkoušet. Šlo to bez problémů. Üplná spokojenost.

  • Brimo
    2020-03-18 06:27:39

    Looks well made. Haven't tested the run out but it's got a good finish to it.

  • 2019-01-03 08:07:06

    I get it, you get what you pay for. But this is collet chuck isn't simply low quality, but actually unusable. The nut has an egg shaped ring out of axis, 6mm thick. The taped shoulder has some deep machining scratches because of the egg shaped milling cut. The collet taped surface is wavey and absolutely not finished. I tried putting a collet inside and it won't even close! The collet won't sit flush inside of it and it wobbles against the taper. Fixing this will cost way more than what this chuck

    Comentários (3)
  • 2019-10-06 08:42:01

    Good quality collet holder. Perfect for home machine shop or small business. Thanks !!

  • bezuidh
    2019-07-18 09:03:55

    exactly as ordered. exelent service.

  • JohnY
    2019-01-28 19:36:34

    Appears to be very well made. Fits my existing ER-32 collets perfectly. Threads are well cut & the nut turns very smoothly. The packaging was inadequate for shipment via Canada Post. It arrived undamaged but the packaging was barely in tact (see photo).


    Go to page


    Você pode estar interessado em

    recommendation for you
    • US$35.99
    • US$32.54
    • US$21.99
    • US$24.99
    • US$19.99
    • US$14.42
    • US$89.93
    • US$38.22
    • US$10.49
    • US$4.32
    • US$22.99
    • US$46.65
    • US$89.99
    • US$38.21
    • US$22.04
    • US$12.99
    • US$47.51
    • US$49.90