Нужная вещь, если не хотите повредить начинку коптера при краше. Отверстия креплений совпадают с отверстиями на раме, ничего доделывать не требуется

Нужная вещь, если не хотите повредить начинку коптера при краше. Отверстия креплений совпадают с отверстиями на раме, ничего доделывать не требуется

Нужная вещь, если не хотите повредить начинку коптера при краше. Отверстия креплений совпадают с отверстиями на раме, ничего доделывать не требуется

The piece I receive had an internal diameter of 5mm for the ZMR frame mounting posts. Only problem is the diameter of the tube is 6mm. Doesn't look practical at first glance to drill out but will try anyway. The external diameter is 7mm so you would be left with a thin 0.5 mm wall thickness. That problem aside it is a quality print and I would recommend it if it fitted my frame. Shame. Disappointed

The piece I receive had an internal diameter of 5mm for the ZMR frame mounting posts. Only problem is the diameter of the tube is 6mm. Doesn't look practical at first glance to drill out but will try anyway. The external diameter is 7mm so you would be left with a thin 0.5 mm wall thickness. That problem aside it is a quality print and I would recommend it if it fitted my frame. Shame. Disappointed

The piece I receive had an internal diameter of 5mm for the ZMR frame mounting posts. Only problem is the diameter of the tube is 6mm. Doesn't look practical at first glance to drill out but will try anyway. The external diameter is 7mm so you would be left with a thin 0.5 mm wall thickness. That problem aside it is a quality print and I would recommend it if it fitted my frame. Shame. Disappointed

keep all your electronics safe and covered up with this. It is a little warped but the 3d print quality is pretty good

keep all your electronics safe and covered up with this. It is a little warped but the 3d print quality is pretty good

keep all your electronics safe and covered up with this. It is a little warped but the 3d print quality is pretty good

I received this last week, but unfortunately the holes are too tight and it doesn't fit on my zmr250, i have a video + photo of it. Can you contact me please?

I received this last week, but unfortunately the holes are too tight and it doesn't fit on my zmr250, i have a video + photo of it. Can you contact me please?

I received this last week, but unfortunately the holes are too tight and it doesn't fit on my zmr250, i have a video + photo of it. Can you contact me please?

Very good product . It is the right size and fit perfect on my zmr250. Very tight but perfect . Good quality plastic . It is strong and don't brake easily . If you want a nice looking zmr250 this is the product that will finish it off

Very good product . It is the right size and fit perfect on my zmr250. Very tight but perfect . Good quality plastic . It is strong and don't brake easily . If you want a nice looking zmr250 this is the product that will finish it off

Very good product . It is the right size and fit perfect on my zmr250. Very tight but perfect . Good quality plastic . It is strong and don't brake easily . If you want a nice looking zmr250 this is the product that will finish it off

Looks good and beneficial to protect inner components also lightweight. However it was very hard to assembly, it was too tight and probably I damaged my red columns to screw. By the way I used a heated nail to open holes for usb and other ports.

Looks good and beneficial to protect inner components also lightweight. However it was very hard to assembly, it was too tight and probably I damaged my red columns to screw. By the way I used a heated nail to open holes for usb and other ports.

Looks good and beneficial to protect inner components also lightweight. However it was very hard to assembly, it was too tight and probably I damaged my red columns to screw. By the way I used a heated nail to open holes for usb and other ports.

Рама выглядит нормально. Немного распирает при одевании на стойки коптера. Ну и придется доработать при конечной инсталляции взади под видеопередатчик с боков что-нибудь подложить на лучи. Да вес 30 грамм.

Рама выглядит нормально. Немного распирает при одевании на стойки коптера. Ну и придется доработать при конечной инсталляции взади под видеопередатчик с боков что-нибудь подложить на лучи. Да вес 30 грамм.

Рама выглядит нормально. Немного распирает при одевании на стойки коптера. Ну и придется доработать при конечной инсталляции взади под видеопередатчик с боков что-нибудь подложить на лучи. Да вес 30 грамм.

Good Quality!!!

Good Quality!!!

Good Quality!!!

carcasa de buen material, muy duradera. 10++++

carcasa de buen material, muy duradera. 10++++

carcasa de buen material, muy duradera. 10++++

This ZMR250 wall kit is pretty nice. It is 3D printed and you can see the layers. It looks like a good print and seems pretty sturdy. It should be strong enough to survive plenty of crashes and should do its job which is to keep dirt and grass out of the inside. The cut aways line up well with the arms and the ESC wires. If you have a tilted camera, you'll have to cut out a little of the top of the camera hole so it will fit around your camera - it's not that hard. Over all it is pretty good. The only bad thing is that it weighs in around 30.7 grams. That is kind of heavy but it does provide a lot of protection for your electronics.

This ZMR250 wall kit is pretty nice. It is 3D printed and you can see the layers. It looks like a good print and seems pretty sturdy. It should be strong enough to survive plenty of crashes and should do its job which is to keep dirt and grass out of the inside. The cut aways line up well with the arms and the ESC wires. If you have a tilted camera, you'll have to cut out a little of the top of the camera hole so it will fit around your camera - it's not that hard. Over all it is pretty good. The only bad thing is that it weighs in around 30.7 grams. That is kind of heavy but it does provide a lot of protection for your electronics.

This ZMR250 wall kit is pretty nice. It is 3D printed and you can see the layers. It looks like a good print and seems pretty sturdy. It should be strong enough to survive plenty of crashes and should do its job which is to keep dirt and grass out of the inside. The cut aways line up well with the arms and the ESC wires. If you have a tilted camera, you'll have to cut out a little of the top of the camera hole so it will fit around your camera - it's not that hard. Over all it is pretty good. The only bad thing is that it weighs in around 30.7 grams. That is kind of heavy but it does provide a lot of protection for your electronics.