Todas as mensagens

KEVIN I haven’t used mine yet but will try to set it up to make 12 volts using my Hit and Miss Engine.

2020-01-14 10:47:43 Útil (0)
Enviar
respostas (2)

KEVIN I just received mine and it came with a small pulley on the side to attach a pull cord to so it can be pull started. It also came with the pull cord. I received mine on December 19.

2019-12-27 12:27:41 Útil (0)
Enviar
respostas (4)

KEVIN I received mine in under two weeks. A lot of the screws were loose. This is not really a big deal as if you’re into this Hobby then you are capable of disassembly and reassembly. The only complaint I have is my engine had the long hex head screws in both flywheels instead of Set Screws. It appears that whoever assembled my engine at the factory was out of the Set Screws and used the long hex head screws that are supposed to be underneath the engine holding the cylinder on. I had to purchase four small metric Set Screws and remove the four wrong hex head screws to install the Correct Set Screws! Then I installed the four hex head screws into the four missing underneath the cylinder. My engine was sealed in the box so it’s obvious that it left the factory in this poor assembly. Bottom line is for the money, mine was $199.00 on sale, you can’t beat the price and quality. The machining, anodizing and fits are well as it should be as this is obviously made on CNC tools. Lubricate all moving parts often and it should have a reasonable life expectancy. You couldn’t built this for triple the price and your time is worth something.

Arnaud D 22/05/2019
6
Comentários (6)

KEVIN I received mine in under two weeks. A lot of the screws were loose. This is not really a big deal as if you’re into this Hobby then you are capable of disassembly and reassembly. The only complaint I have is my engine had the long hex head screws in both flywheels instead of Set Screws. It appears that whoever assembled my engine at the factory was out of the Set Screws and used the long hex head screws that are supposed to be underneath the engine holding the cylinder on. I had to purchase four small metric Set Screws and remove the four wrong hex head screws to install the Correct Set Screws! Then I installed the four hex head screws into the four missing underneath the cylinder. My engine was sealed in the box so it’s obvious that it left the factory in this poor assembly. Bottom line is for the money, mine was $199.00 on sale, you can’t beat the price and quality. The machining, anodizing and fits are well as it should be as this is obviously made on CNC tools. Lubricate all moving parts often and it should have a reasonable life expectancy. You couldn’t built this for triple the price and your time is worth something.

misfitsailor 14/01/2018
24
Comentários (1)

KEVIN I received mine in under two weeks. A lot of the screws were loose. This is not really a big deal as if you’re into this Hobby then you are capable of disassembly and reassembly. The only complaint I have is my engine had the long hex head screws in both flywheels instead of Set Screws. It appears that whoever assembled my engine at the factory was out of the Set Screws and used the long hex head screws that are supposed to be underneath the engine holding the cylinder on. I had to purchase four small metric Set Screws and remove the four wrong hex head screws to install the Correct Set Screws! Then I installed the four hex head screws into the four missing underneath the cylinder. My engine was sealed in the box so it’s obvious that it left the factory in this poor assembly. Bottom line is for the money, mine was $199.00 on sale, you can’t beat the price and quality. The machining, anodizing and fits are well as it should be as this is obviously made on CNC tools. Lubricate all moving parts often and it should have a reasonable life expectancy. You couldn’t built this for triple the price and your time is worth something.

gerald62linnett 19/06/2019
0
Comentários (1)

KEVIN I received mine in under two weeks. A lot of the screws were loose. This is not really a big deal as if you’re into this Hobby then you are capable of disassembly and reassembly. The only complaint I have is my engine had the long hex head screws in both flywheels instead of Set Screws. It appears that whoever assembled my engine at the factory was out of the Set Screws and used the long hex head screws that are supposed to be underneath the engine holding the cylinder on. I had to purchase four small metric Set Screws and remove the four wrong hex head screws to install the Correct Set Screws! Then I installed the four hex head screws into the four missing underneath the cylinder. My engine was sealed in the box so it’s obvious that it left the factory in this poor assembly. Bottom line is for the money, mine was $199.00 on sale, you can’t beat the price and quality. The machining, anodizing and fits are well as it should be as this is obviously made on CNC tools. Lubricate all moving parts often and it should have a reasonable life expectancy. You couldn’t built this for triple the price and your time is worth something.

Boontoe 21/05/2019
0
Comentários (1)

KEVIN I received mine in under two weeks. A lot of the screws were loose. This is not really a big deal as if you’re into this Hobby then you are capable of disassembly and reassembly. The only complaint I have is my engine had the long hex head screws in both flywheels instead of Set Screws. It appears that whoever assembled my engine at the factory was out of the Set Screws and used the long hex head screws that are supposed to be underneath the engine holding the cylinder on. I had to purchase four small metric Set Screws and remove the four wrong hex head screws to install the Correct Set Screws! Then I installed the four hex head screws into the four missing underneath the cylinder. My engine was sealed in the box so it’s obvious that it left the factory in this poor assembly. Bottom line is for the money, mine was $199.00 on sale, you can’t beat the price and quality. The machining, anodizing and fits are well as it should be as this is obviously made on CNC tools. Lubricate all moving parts often and it should have a reasonable life expectancy. You couldn’t built this for triple the price and your time is worth something.

nappa 20/03/2019
1
Comentários (4)