Todas as mensagens

Q: Can you place a call from the watch?

perguntado por Chilimong sobre 2020-04-27 06:37:05

funkycowie@gmail.com no, it's not that advanced

2024-02-17 06:06:36 Útil (0)
Enviar
respostas (5)

funkycowie@gmail.com The button only turns the screen on and off, although it rotates it does nothing, you use the touch screen to navigate.

2023-11-04 08:00:14 Útil (0)
Enviar
respostas (4)

Q: Can control music?

perguntado por BG411054312 sobre 2020-06-26 10:35:23

funkycowie@gmail.com no, it can't, it is strictly a monitoring device that connects to your phone via an app.

2023-11-04 07:58:32 Útil (0)
Enviar
respostas (3)

Q: Is the screen face scratch-free protection?

perguntado por Billy sobre 2021-04-03 04:47:57

funkycowie@gmail.com no but I have bashed mine many times and it still looks like new, they are really well made.

2023-07-20 12:32:52 Útil (0)
Enviar
respostas (3)

Q: What is the voltage of the product?

perguntado por geovanesilvajoo sobre 2019-09-30 05:00:22

funkycowie@gmail.com it's usb powered so 5v

2023-07-20 12:31:37 Útil (0)
Enviar
respostas (1)

Q: Tem 30 dias que comprei e segue em processamento?

perguntado por BG332124161 sobre 2020-09-24 12:01:37

funkycowie@gmail.com you need to contact support via chat otherwise they will likely not see this

2023-07-02 12:20:46 Útil (0)
Enviar
respostas (3)
funkycowie@gmail.com 23/06/2023
I would have given this 5 stars however due to a missing microswitch and the fact two out of the 5 stepper drivers were just laying on top of the main board, for this I have marked it down. TwoTrees are sending out the part FOC but because it's coming from their China location it could take 4-6 weeks, other than that building the printer was relatively easy and the printer at stock is far better than my previous one, a JGAurora A5. People say the stock hot is bad but I am finding it works just as well if not slightly better than my previous 3D printer, the core xy set up providing better quality prints than the bed slinger. However whilst the printer works fine at stock it is very modifiable and that is the reason most people should purchase this. Put some higher performing parts on and you have a printer that can achieve increased speed and quality for cheaper than one prebuilt and have some fun building it. I have just added a 3D touch, BLTouch clone which is easy to activate within the firmware, you do need an extension cable though, next I will be moving the dual gear extruder to the head, more extension cables required, then I will. be replacing the firmware with Klipper and replacing the hotend so I can print faster. I only have two criticisms of this printer, the SD slot is on the left side when it could have been on the front, and the power cable is plugged in the right side. This combined with the extruder being on the left make the printer wider than the stated dimensions so I have had to change my heated cabinet set up to accommodate it. It's a well built machine that works well if treated right from the beginning. The 8th photo below shows the print of the direct drive holder and the BLTouch clone holder that was done with the standard hot end.
0
Recomendações
Comentários (0)

Q: Does this product hook onto a door?

perguntado por BG101855551 sobre 2020-04-30 06:36:33

funkycowie@gmail.com It does but be careful if you thread them through the door hook as they will wear quickly as the rubber will get cut through.

2021-01-03 11:37:15 Útil (0)
Enviar
respostas (5)

Q: Do the blades lock in place or have spring assist to open?

perguntado por BG375093822 sobre 2020-09-18 02:46:58

funkycowie@gmail.com It locks in place with a bit of spring steel that you need to push pack to return the blade to the handle.

2020-12-13 03:21:07 Útil (0)
Enviar
respostas (3)

Q: Type of steel is 5CR18. What means M390 on this Knife?

perguntado por MarkT4 sobre 2020-12-13 01:10:29

funkycowie@gmail.com M390is one of the new super steels on the block, manufactured by Bohler-Uddeholm (result of merger of Austrian Bohler and Swedish Uddeholm). It uses third generation powder metal technology and developed for knife blades requiring excellent corrosion resistance and very high hardness for excellent wear resistance.

2020-12-13 03:19:34 Útil (0)
Enviar
respostas (1)

Q: what is the length of the ropes?

perguntado por BG571744184 sobre 2020-10-19 10:22:35

funkycowie@gmail.com 120cm, instructions state they should not be stretched more than 360cm.

2020-11-29 10:28:39 Útil (0)
Enviar
respostas (4)