If you have EINHELL BT-ML300 it will work well. Check the numbering when mounting.

If you have EINHELL BT-ML300 it will work well. Check the numbering when mounting.

If you have EINHELL BT-ML300 it will work well. Check the numbering when mounting.

К патрону на 80 мм подходят идеально. Номер у всех кулачков одинаковый. Прилегание кулачков плотное но растачивать все равно прийдется.

К патрону на 80 мм подходят идеально. Номер у всех кулачков одинаковый. Прилегание кулачков плотное но растачивать все равно прийдется.

К патрону на 80 мм подходят идеально. Номер у всех кулачков одинаковый. Прилегание кулачков плотное но растачивать все равно прийдется.

A entrega original, infelizmente, chegou defeituosa da França e foi imediatamente reclamada: o Spannjawe No 3 era o dobro, o No 1 estava faltando para ele. No entanto, após alguns e-mails, um substituto foi-me entregue. São maxilas duras, que devem ser tidas em conta ao utilizá-las. Eles correm perfeitamente e sem brincadeira. Usado em um maxilar de 300 mais com revestimento de 80.

Die ursprüngliche Lieferung kam leider fehlerhaft aus Frankreich an und wurde umgehend reklamiert: Spannbacke Nr. 3 war doppelt, die Nr. 1 fehlte dafür. Nach einigen Emails wurde mir dann aber Ersatz geliefert. Es sind harte Spannbacken, was man beim Einsatz berücksichtigen sollte. Sie laufen einwandfrei und ohne Spiel. Eingesetzt in einer 300er Einhell mit 80er Futter.

A entrega original, infelizmente, chegou defeituosa da França e foi imediatamente reclamada: o Spannjawe No 3 era o dobro, o No 1 estava faltando para ele. No entanto, após alguns e-mails, um substituto foi-me entregue. São maxilas duras, que devem ser tidas em conta ao utilizá-las. Eles correm perfeitamente e sem brincadeira. Usado em um maxilar de 300 mais com revestimento de 80.

These fitted my 8 year old 80mm 3 jaw chuck, on an Axminster / Sieg C2 lathe. The chuck bears the name 'Tian Pai'.on a sticker. I obtained the lathe second hand with no outside jaws for the chuck. The run out using a 12 mm drill is acceptable (without any tweaking) at 2.5 thousandths inch, I suspect de-burring the sharp edges on the new jaws, and bumping the chuck run out could be used to reduce the over all runout. Very pleased with my decision to take the risk much cheaper than a new chuck. I can't guarantee that they will fit your chuck, check the measurements given carefully against you own inside chuck jaws as I did.

These fitted my 8 year old 80mm 3 jaw chuck, on an Axminster / Sieg C2 lathe. The chuck bears the name 'Tian Pai'.on a sticker. I obtained the lathe second hand with no outside jaws for the chuck. The run out using a 12 mm drill is acceptable (without any tweaking) at 2.5 thousandths inch, I suspect de-burring the sharp edges on the new jaws, and bumping the chuck run out could be used to reduce the over all runout. Very pleased with my decision to take the risk much cheaper than a new chuck. I can't guarantee that they will fit your chuck, check the measurements given carefully against you own inside chuck jaws as I did.

These fitted my 8 year old 80mm 3 jaw chuck, on an Axminster / Sieg C2 lathe. The chuck bears the name 'Tian Pai'.on a sticker. I obtained the lathe second hand with no outside jaws for the chuck. The run out using a 12 mm drill is acceptable (without any tweaking) at 2.5 thousandths inch, I suspect de-burring the sharp edges on the new jaws, and bumping the chuck run out could be used to reduce the over all runout. Very pleased with my decision to take the risk much cheaper than a new chuck. I can't guarantee that they will fit your chuck, check the measurements given carefully against you own inside chuck jaws as I did.

Na primeira entrega, infelizmente, 2x braçadeiras, o maxilar número 1 foi entregue, portanto inutilizável. As próprias mandíbulas de fixação são mandíbulas duras e são limpas.

Bei der ersten Lieferung leider 2x Spannbacke Nummer 1 geliefert bekommen, somit unbrauchbar. Ersatzlieferung nach einigem Emailverkehr bekommen. Die Spannbacken an sich sind harte Backen und sauber gefertigt.

Na primeira entrega, infelizmente, 2x braçadeiras, o maxilar número 1 foi entregue, portanto inutilizável. As próprias mandíbulas de fixação são mandíbulas duras e são limpas.

Obrigado, já percebi. A qualidade é baixa, mas o cartucho subiu normalmente. Comprado para serrar e experimentar, tão satisfeito.

Thank you, I got it. The quality is low, but the cartridge got up normally. Bought for sawing and experimenting, so overall satisfied.

Obrigado, já percebi. A qualidade é baixa, mas o cartucho subiu normalmente. Comprado para serrar e experimentar, tão satisfeito.

Perfetto!

Perfetto!

Perfetto!

Precies de juiste maat buitenbekken voor een ander merk klauwplaat. Ik ben helemaal blij.

Precies de juiste maat buitenbekken voor een ander merk klauwplaat. Ik ben helemaal blij.

Precies de juiste maat buitenbekken voor een ander merk klauwplaat. Ik ben helemaal blij.

Tovar došil v poriadku

Tovar došil v poriadku

Tovar došil v poriadku

Exactly as discribed.Fits perfect on my mini lathe.A sale well done.Thank you.

Exactly as discribed.Fits perfect on my mini lathe.A sale well done.Thank you.

Exactly as discribed.Fits perfect on my mini lathe.A sale well done.Thank you.