please help connected all up. everything works except for the motor. just makes continued biep biep biep biep. I switched wires around in every possible way. Same result Everytime. thanks.

please help connected all up. everything works except for the motor. just makes continued biep biep biep biep. I switched wires around in every possible way. Same result Everytime. thanks.

please help connected all up. everything works except for the motor. just makes continued biep biep biep biep. I switched wires around in every possible way. Same result Everytime. thanks.

These can be flashed with Simonk. You need an 8MHz build of tgy.hex. These have no external oscillator. The hardware is fairly low quality, but given the price they're more than adequate. P-CH FETs are TPC8111, and N-CH are IRF7832

These can be flashed with Simonk. You need an 8MHz build of tgy.hex. These have no external oscillator. The hardware is fairly low quality, but given the price they're more than adequate. P-CH FETs are TPC8111, and N-CH are IRF7832

These can be flashed with Simonk. You need an 8MHz build of tgy.hex. These have no external oscillator. The hardware is fairly low quality, but given the price they're more than adequate. P-CH FETs are TPC8111, and N-CH are IRF7832

Fonctionne très bien et pas cher, je ne peux pas dire quelque chose à propos de la qualité, mais apres calibrage il semble ok pour moi j'ai souder les fils directement pour gagner du poid ;)

Fonctionne très bien et pas cher, je ne peux pas dire quelque chose à propos de la qualité, mais apres calibrage il semble ok pour moi j'ai souder les fils directement pour gagner du poid ;)

Fonctionne très bien et pas cher, je ne peux pas dire quelque chose à propos de la qualité, mais apres calibrage il semble ok pour moi j'ai souder les fils directement pour gagner du poid ;)

spedizione super veloce e prodotto conforme alla descrizione

spedizione super veloce e prodotto conforme alla descrizione

spedizione super veloce e prodotto conforme alla descrizione

I ordered 6 of these. As the first review suggested, the tgy-version of the simonK firmware works with these ESCs. You need to change F_CPU to 8000000 since these boards use the internal oscillator. This is no problem with the kkMutlicopter flash tool, since it allows you to build the source. These ESCs get very warm. At roughly 5 amps the P-fets started burning my fingers. Lowering the PWM frequency to 8kHz helped somewhat. The stock FW uses 7.8kHz PWM (verified with scope). The quality is ok, but not high. There is quite a lot of flux residue on the PCB. The electrolytic cap is placed badly on the PCB. And this is also a bare miminum component ESC, which is really no surprise. These ESCs should be good for very small copters!

I ordered 6 of these. As the first review suggested, the tgy-version of the simonK firmware works with these ESCs. You need to change F_CPU to 8000000 since these boards use the internal oscillator. This is no problem with the kkMutlicopter flash tool, since it allows you to build the source. These ESCs get very warm. At roughly 5 amps the P-fets started burning my fingers. Lowering the PWM frequency to 8kHz helped somewhat. The stock FW uses 7.8kHz PWM (verified with scope). The quality is ok, but not high. There is quite a lot of flux residue on the PCB. The electrolytic cap is placed badly on the PCB. And this is also a bare miminum component ESC, which is really no surprise. These ESCs should be good for very small copters!

I ordered 6 of these. As the first review suggested, the tgy-version of the simonK firmware works with these ESCs. You need to change F_CPU to 8000000 since these boards use the internal oscillator. This is no problem with the kkMutlicopter flash tool, since it allows you to build the source. These ESCs get very warm. At roughly 5 amps the P-fets started burning my fingers. Lowering the PWM frequency to 8kHz helped somewhat. The stock FW uses 7.8kHz PWM (verified with scope). The quality is ok, but not high. There is quite a lot of flux residue on the PCB. The electrolytic cap is placed badly on the PCB. And this is also a bare miminum component ESC, which is really no surprise. These ESCs should be good for very small copters!

За эту цену неплохие регуляторы. Брал 6 штук - 4 на коптер и 2 в запас. Работают все. Прошил Simonk TGY через kkMulticopterFlashTool. В качестве ISP программатора использовал Arduino Uno.

За эту цену неплохие регуляторы. Брал 6 штук - 4 на коптер и 2 в запас. Работают все. Прошил Simonk TGY через kkMulticopterFlashTool. В качестве ISP программатора использовал Arduino Uno.

За эту цену неплохие регуляторы. Брал 6 штук - 4 на коптер и 2 в запас. Работают все. Прошил Simonk TGY через kkMulticopterFlashTool. В качестве ISP программатора использовал Arduino Uno.

produit bien emballé a voir qualité après essais

produit bien emballé a voir qualité après essais

produit bien emballé a voir qualité après essais

Ok

Ok

Ok

nice cheap esc, i use it with BE1806 motors on an hexacopter,but if you want to use the full capabilities of this ESC , you must reflash it with Simonk firmware

nice cheap esc, i use it with BE1806 motors on an hexacopter,but if you want to use the full capabilities of this ESC , you must reflash it with Simonk firmware

nice cheap esc, i use it with BE1806 motors on an hexacopter,but if you want to use the full capabilities of this ESC , you must reflash it with Simonk firmware

elama this is products .elama this is products .elama this is products .

elama this is products .elama this is products .elama this is products .

elama this is products .elama this is products .elama this is products .