Todas as mensagens

Q: Is this tinned pure copper or is it CCA wire?

perguntado por BG225733103 sobre 2022-10-04 12:13:40

Burplerlcbm tinned copper

2022-10-05 08:22:57 Útil (0)
Enviar
respostas (1)

Q: What is RTC for each tip?

perguntado por BG143912477 sobre 2022-03-19 01:31:58

BG225733103 RTC? Wich definition of RTC are you talking about? Your Question makes no sense...There are lots of different meanings for RTC. See here: en.wikipedia.org | wiki | RTC If you want people to help you stop using acronyms and give more context instead of just a short question.

2022-03-19 04:06:24 Útil (0)
Enviar
respostas (2)

BG225733103 Sure looks like a scalpell blade to me. The blade shown here seems to be for use with a scalpell handle no 3 or 4. Blade shape could be a Rüttgers no 11 or an Aesculap no 25. But the mounting slot is the same for all blade shapes, so you can use any shape you like. Use your favorite image search engine to search for "scalpell blade shapes" to find the one you want.

2021-09-16 03:45:51 Útil (1)
Enviar
respostas (2)

Q: What kinds of probes/leads should I use?

perguntado por cubeconvict sobre 2019-06-27 10:47:07

BG225733103 Bare wire is probably best. I suspect that it was never intended for banana plugs, but as pure screw terminals. Hole diameter in the plastic head is about 5.5mm.

2021-08-29 01:06:26 Útil (0)
Enviar
respostas (6)

Q: what kind of fuses use? 5x20 mm? and how much amperes are each one?

perguntado por pjlabarta sobre 2019-09-29 08:59:13

BG225733103 I suspect that the fuses that are currently present will be installed with respect to the current. My board contained 5A fuses.

2021-08-29 12:57:48 Útil (0)
Enviar
respostas (6)

Q: Can I get 24V by connection with 12V and -12V?

perguntado por BG405471057 sobre 2021-08-22 02:03:19

BG225733103 On the board is no circuitry that would prevent you from using the +12V with the -12V instead of GND - the screw terminals are connected straight to the ATX connector via a fuse only. So yes, you __could__ get a 24V potential. If it works or if it goes bang depends entirely on the ATX PSU that you connect to the board.

2021-08-29 12:50:15 Útil (0)
Enviar
respostas (8)

Q: Are their 220 Ohm and 10 k values resistors?

perguntado por BG019391538 sobre 2021-08-03 04:09:34

BG225733103 all Ω values are listed in the overview.

2021-08-03 10:36:45 Útil (1)
Enviar
respostas (9)

Q: do you have 1k resistors included

perguntado por BG153723470 sobre 2020-11-06 07:54:55

BG225733103 1kΩ is listed in the value list shown in the overview, so yes there are 20 pieces.

2021-08-03 10:33:15 Útil (0)
Enviar
respostas (2)

Q: How much current does it draw?

perguntado por BG225733103 sobre 2021-06-22 07:09:26

Joao 12v

2021-07-14 09:58:55 Útil (0)
Enviar
respostas (1)

BG225733103 So...Where are the pictures of the grown plants? It's been 22 months...

jrgunder 17/08/2019
0
Comentários (1)

BG225733103 Inthe description it says 3mm. Measured with a caliper the shanks are between 3,09mm and 3.16mm

2021-05-25 06:21:04 Útil (0)
Enviar
respostas (2)

BG225733103 Isthe LED indicating power on? If yes, make sure the 5A fuses aren't blown.

2021-05-25 06:16:21 Útil (0)
Enviar
respostas (8)